Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
They are making several good annotation related to Tools You Need to Install a New Bathtub overall in this content in the next paragraphs.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a bathtub isn't exactly rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is likewise a moderately tough job. If the old tub is readily obtainable, the task can move quickly; if you have to open up a wall surface to remove the old bathtub as well as position the new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a specialist to take over a halfway-completed job, it is better to think about using one before you begin. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly assist you mount a brand-new tub in your bathroom if you have actually already gotten a new bathtub and do not need to alter the arrangement of your previous water system pipes.
Your devices and product list must consist of the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The process of getting rid of the existing taps can be fairly problematic because of the limited access that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. Once the supply pipes have actually been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washers are in place between the faucet as well as the sink. Secure the tap in place with the maker supplied backnut. When the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the required position. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system and also inspect all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, fix the bath paneling as described in the supplier's user's manual. Tiling and also securing around the tub ought to wait till the tub has been made use of a minimum of once as this will certainly settle it right into its final position.
Planning for the Setup
To start with, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the flexible faucet connectors to the bottom of both faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealer can break relatively very early if you do not consider this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our section on A Step-by-Step Guide to Installing a Bathtub. Thanks so much for finding the time to read through our short article. Do you know another person who is sincerely interested in the subject? Why not promote it. Thank you so much for going through it.
This Resource Report this page